Product Reviews

Donner DP-1 Guitar Power Supply Review: Ten Outputs for a Pedalboard

A compact option for guitarists powering a mixed 9V, 12V, and 18V pedalboard who want multiple outputs and short-circuit protection.

This article contains affiliate links. We may earn a commission if you buy through them, at no extra cost to you.

The Donner DP-1 Guitar Power Supply review is most relevant to players who want one compact unit for a board with several pedals and a mix of voltage needs.

Its ten outputs cover common 9V connections plus one each at 12V and 18V, though current limits mean checking every pedal's requirements first.

Donner DP-1 Review Summary

The quick verdict

Donner DP-1 Guitar Power Supply
4.5/5

7,000+ ratings

Read Amazon Reviews

Donner DP-1 Guitar Power Supply

A compact option for guitarists powering a mixed 9V, 12V, and 18V pedalboard who want multiple outputs and short-circuit protection.

  • Ten outputs: seven 9V outputs at 100mA, one 9V output at 500mA, one 12V output at 100mA, and one 18V output at 100mA.
  • AC input range of 100–240V; the supply uses an 18V DC input.
  • Independent short-circuit protection is designed to keep other outputs working if one output is shorted.
  • Circuit design aims to provide an isolation effect, with the manufacturer clarifying that the circuit is not absolutely isolated.

Pros

  • Ten outputs offer room to power several pedals from one supply.
  • The mix of 9V, 12V, and 18V outputs can suit boards with different voltage requirements.

Consider before buying

  • Nine of the ten outputs are rated at only 100mA, so current draw can limit which pedals can be connected.
  • The design's isolation is described as an effect rather than absolute circuit isolation; players with strict isolation requirements should verify suitability.
Read the full review summary

The DP-1 combines seven 9V outputs rated at 100mA each with a higher-current 9V output rated at 500mA, plus single 12V and 18V outputs rated at 100mA.

It includes ten power cables, uses an aluminum alloy enclosure, and accepts 100–240V AC input. That makes it a flexible starting point for a board whose pedals fit those output limits.

Its independent short-circuit protection is designed so a fault on one output does not stop the others from working.

The manufacturer describes the supply as using circuit simulation and design to achieve an isolation effect, while clarifying that this is not absolute circuit isolation.

Buyers who require fully isolated outputs should confirm the design meets their standard before choosing it.

The buying factors

Donner DP-1 Scorecard

Editorial scores reflect listed features and buyer fit; they are not laboratory measurements or customer ratings.

8/10

Output variety

Ten connections cover three voltage options, with eight outputs at 9V and one each at 12V and 18V.

6/10

Current flexibility

One 9V output offers 500mA, while the other nine are rated at 100mA each, so compatibility depends on each pedal's draw.

8/10

Board capacity

Ten included power cables and ten outputs can serve a board with multiple compatible pedals.

7/10

Fault isolation

Independent short-circuit protection is intended to let other outputs continue if one output is shorted; the design is not described as absolutely isolated.

8/10

Portability

The compact rectangular aluminum alloy unit is listed at 6.9 ounces, which should be manageable on many pedalboards.

6/10

Setup clarity

The voltage and current options are specific, but buyers still need to match each pedal to the correct output.

Key Features and Specifications of Donner DP-1

  • Ten outputs: seven 9V outputs at 100mA, one 9V output at 500mA, one 12V output at 100mA, and one 18V output at 100mA.
  • AC input range of 100–240V; the supply uses an 18V DC input.
  • Independent short-circuit protection is designed to keep other outputs working if one output is shorted.
  • Circuit design aims to provide an isolation effect, with the manufacturer clarifying that the circuit is not absolutely isolated.
  • Aluminum alloy enclosure in a compact rectangular form; listed weight is 6.9 ounces.
  • Includes ten power cables and a blue LED used for indication and pedalboard lighting.

Pros and Cons of Donner DP-1

Pros

  • Ten outputs offer room to power several pedals from one supply.
  • The mix of 9V, 12V, and 18V outputs can suit boards with different voltage requirements.
  • A 500mA 9V connection accommodates a higher-current pedal than the 100mA outputs, provided its requirements fit.
  • Independent short-circuit protection is designed to help a fault on one output leave the others operating.

Consider before buying

  • Nine of the ten outputs are rated at only 100mA, so current draw can limit which pedals can be connected.
  • The design's isolation is described as an effect rather than absolute circuit isolation; players with strict isolation requirements should verify suitability.
  • The 12V and 18V connections are each limited to 100mA, so check whether the intended pedal fits those ratings.

Who Should Buy Donner DP-1?

Good fit

Consider the DP-1 if your board uses several pedals that match its output voltages and current limits. The seven 9V/100mA outputs cover lower-draw pedals, while the separate 9V/500mA output gives you another option for a compatible higher-draw unit.

It may also make sense if you want 12V and 18V connections on the same supply, or value a compact aluminum body and a cable for each output.

Before ordering, make a list of each pedal's voltage, polarity, connector, and current draw, then map those needs to the DP-1's outputs.

If your priorities include protection against one shorted connection disrupting the whole board, the independent protection design is relevant.

Treat the isolation note carefully: if your setup depends on absolute isolation, confirm the technical design with the manufacturer before relying on it.

Who should skip it

Look elsewhere if your pedals need more than 500mA from a single 9V output, or if a 12V or 18V pedal draws more than 100mA. The listed ratings do not support those combinations.

This is also a poor fit if your board requires outputs that are confirmed as absolutely isolated. The design is described as creating an isolation effect, with an explicit qualification that it is not absolute.

How the Donner DP-1 Fits a Multi-Pedal Board

Match output current to each pedal

Voltage alone is not enough when assigning pedals to a power supply.

The DP-1 offers one 9V connection at 500mA and seven at 100mA, so check each pedal's stated current draw and reserve the higher-current output for a device that needs it and stays within that rating.

Use the less common voltages selectively

The single 12V and 18V outputs can reduce the need to plan around 9V-only power, but each is rated at 100mA.

Confirm both the pedal's required voltage and its current draw before connecting it; a matching voltage by itself does not establish compatibility.

Understand the isolation qualification

Independent short-circuit protection addresses one specific failure case: the design is intended to let the other outputs keep working if one is shorted.

That is useful board-level protection, but it does not establish absolute isolation, so players sensitive to noise or strict about isolation should verify the circuit details for their setup.

Plan the physical setup

The aluminum alloy enclosure, compact rectangular form, 6.9-ounce listed weight, ten cables, and blue LED point toward a supply intended to sit with a multi-pedal rig.

Check your board's available space and cable routing, then make sure the included barrel connectors suit your pedals.

Alternatives to Donner DP-1

No alternative model is recommended here. Compare the output voltage, current limits, and isolation design that matter to your board before choosing another supply.

Is Donner DP-1 Worth It?

The Donner DP-1 is worth considering for a multi-pedal board whose needs fit its ten outputs, particularly if you want 9V connections alongside 12V and 18V options.

Its included cables, compact aluminum enclosure, and independent short-circuit protection make it a practical candidate to evaluate.

Check every pedal's voltage and current requirements before buying, with special attention to the many 100mA outputs and the qualified isolation design.

Choose it when those limits match your rig; confirm the circuit details first if absolute isolation is essential.

Your review at a glance

Donner DP-1 Guitar Power Supply
4.5/5

7,000+ ratings

Read Amazon Reviews

Donner DP-1 Guitar Power Supply

A compact option for guitarists powering a mixed 9V, 12V, and 18V pedalboard who want multiple outputs and short-circuit protection.

  • Ten outputs: seven 9V outputs at 100mA, one 9V output at 500mA, one 12V output at 100mA, and one 18V output at 100mA.
  • AC input range of 100–240V; the supply uses an 18V DC input.
  • Independent short-circuit protection is designed to keep other outputs working if one output is shorted.
  • Circuit design aims to provide an isolation effect, with the manufacturer clarifying that the circuit is not absolutely isolated.

Written by

frontiersmetalfestival.com Editorial Team

Editorial team

frontiersmetalfestival.com publishes practical how-to guides and educational articles with clear steps and useful context.

Amazon customer reviews

See what buyers think

Explore customer reviews, photos and available video reviews on Amazon.

Donner DP-1 Guitar Power Supply

Donner DP-1 Guitar Power Supply

A compact option for guitarists powering a mixed 9V, 12V, and 18V pedalboard who want multiple outputs and short-circuit protection.

  • Ten outputs: seven 9V outputs at 100mA, one 9V output at 500mA, one 12V output at 100mA, and one 18V output at 100mA.
  • AC input range of 100–240V; the supply uses an 18V DC input.
Check Video Reviews on Amazon